How-to guide

How to price a sign: materials, production time, installation and margin

Intermediate10 min read

Zigaflow Editorial

Published

Zigaflow Editorial publishes Zigaflow's guides, insights, industry resources, glossary and workflow pages. Zigaflow is responsible for what they say. Spotted an error? Email support@zigaflow.com.

In short

Price a sign from material by area with waste, production time, artwork and proofs, and installation. Quote installation as its own line, including access equipment, because that is where sign jobs most often lose margin.

  • Price material by area and add waste before applying any markup.
  • Cost production time at a shop rate built from overhead, profit and billable hours.
  • Give artwork and proofs their own line with a stated number of revisions.
  • Price installation as a separate line using crew-hours, access equipment, permits and electrical work.
  • Check the margin and the market before the quote goes out.

Build a sign price from material by area with waste, production time, artwork and proofs, and installation with its access equipment, and learn why installation deserves its own line on every quote.

A sign maker should build the price of a sign from four separate parts: material measured by area with waste added, production time at a shop rate that covers overhead, artwork and proofs, and installation with its access equipment. Each of those needs its own line on the quote, and installation needs the clearest one. It is the part of a sign job where margin most often disappears, because the site is unknown until someone is standing in front of it. This guide walks through the build-up in the order you would work it.

Why one lump-sum price hides the problem

A single figure for "supply and fit one illuminated fascia sign" feels simple for the customer. It is dangerous for you. When the job finishes over budget, you cannot tell whether the vinyl, the router hours or the day on a lift caused it, so the next quote repeats the mistake.

Labor weighs heavily in this trade. Sign Customiser, citing the 2022 US Economic Census, reports that payroll was 28.4% of the value of shipments for US sign manufacturers, against 11.5% across all manufacturing. A shop that marks up materials correctly but underprices hours still loses money. Separate lines make each estimate checkable against the actual job afterwards.

1

Measure the material by area and add waste

Work out the area of every substrate, vinyl, laminate and board in the job, then convert each into a cost per square foot or square meter from what you actually paid, including shipping. A sheet that costs $65 and yields 32 square feet costs about $2.03 per square foot. Add waste before you apply any markup. Offcuts you cannot resell, test cuts, misprints and weeding losses are real costs, and even tightly nested acrylic work can waste around 10% of a sheet according to a trade article cited by Sign Customiser. Include ink and consumables per square foot of print.

2

Mark up materials and bought-in parts

Apply your material markup to the area cost plus waste. For parts you buy in, such as channel letters from a fabricator, power supplies or LED modules, add what you pay plus a handling markup that covers ordering, storage and the risk of a supplier error. Keep that markup defensible: a trade writer quoted by Sign Customiser warns that customers who learn what a subcontractor charged tend to resent more than about 20% on top. If you target a margin rather than a markup, divide cost by one minus the margin. Costs of $50 at a 50% margin sell for $100, not $75.

3

Price production time at a full shop rate

Estimate hours for each stage separately: printing, cutting, routing, fabrication, finishing and assembly. Multiply by a shop rate built from yearly running costs plus your profit target, divided by billable hours rather than paid hours. Quoting, cleaning, maintenance and chasing payments are not billable, so a 40-hour week might only bill 30. Where a router, laser or wide-format printer does most of the work, some shops add a machine-hour rate. The shop rate already contains overhead and profit, so do not stack another margin on the labor line.

4

Charge for artwork and proofs

Design time is production time that happens before any material is cut. Give artwork, vectorizing, layout and proof rounds their own line, with a stated number of included revisions. A proof that goes back three times without a charge is hours given away. Agree the approved proof as the specification, so a later change to size, color or copy becomes a priced variation instead of an argument at handover.

5

Survey the site before you price installation

Installation cost depends on mounting height, wall construction, sign weight, electrical access, pedestrian or traffic control, landlord rules, travel and the number of people needed. SignPricer lists these among the factors that change the cost of a commercial installation. Where you cannot visit, ask for photos with a tape measure in frame, the wall type and the height of the fixing point. If information is missing, say so on the quote and state an allowance rather than hiding the unknown inside profit.

6

Price installation as its own line

Count crew-hours, not clock hours: two installers working three hours is six labor hours. Add loading, travel, site preparation and cleanup when they belong to the job. Then add hardware, anchors, patching and disposal as separate costs. Keep this line apart from fabrication, so you can see over time whether your fitting estimates hold. Work out a fitting rate the same way you worked out the shop rate, with vehicle and insurance costs included, instead of borrowing the workshop figure.

7

Add access equipment, permits and electrical work

Lifts, cranes, scaffold, traffic control and permits are costs you pay whether or not the sign goes up first time. Include rental, delivery, fuel and operator fees in job cost, then apply the same documented pricing rule you use elsewhere. Check permit, engineering and licensed electrical requirements for the local area separately, because they differ by place and are the customer's or your responsibility depending on the contract. List any licensed electrician or subcontractor as documented outside cost.

8

Check the margin and the market, then send the quote

Add the lines and calculate what the job earns: price minus materials, bought-in parts and wages, divided by price. Compare the result with your target, and check the markup against margin arithmetic so you do not confuse the two. Then compare the floor price with what comparable shops charge. If you are above the market, find the cost that is out of line before cutting price. If you are well below it, you are probably underpricing.

A worked example with installation split out

These are illustrative round numbers, not benchmarks. A 4 by 8 foot printed panel for a shopfront uses 32 square feet of substrate and print. Materials cost $200 including waste, marked up to $400. Production is 3 hours at a $90 shop rate, so $270. Artwork and two proofs add 1 hour at the same rate, $90. Installation is two people for 3 hours, so 6 crew-hours at a $75 fitting rate, $450, plus $180 for a one-day lift hire and $40 for anchors.

The sign itself is $760. Installation is $670, nearly as much again. Had the quote read "supply and fit, $1,000", a lift that cost twice as much or a second visit would have taken the whole profit from the fitting side. On a separate line, the quote either covers it or you can see exactly what to change.

Common pitfalls

The first is pricing installation as a percentage of the sign. A small sign on a tall building costs more to fit than a large sign at ground level. The second is quoting without a survey, then absorbing a wall that cannot take the fixings. The third is applying margin twice: once through the shop rate and again on the whole job, which prices you out of work you should win.

Turning the build-up into a repeatable quote

Once the lines are fixed, reuse them. A quote that always lists material, production, artwork and proofs, installation and access equipment lets you compare estimated against actual hours on every job. The margin calculator helps you check each target margin, and the signage quote template gives you a starting layout. Sign makers can read more on the signage industry page. If you build quotes in software, Zigaflow quotes are where these lines would live.

Common questions

Add the waste your own jobs actually produce, and measure it by comparing material bought with material sold over several jobs. Offcuts you cannot resell, test cuts, misprints and weeding losses all count. One trade article cited by Sign Customiser notes that even tightly nested acrylic work can waste around 10% of a sheet, so a figure of zero is almost always wrong. Apply waste before markup so it is recovered in the price.

Sources

See it in Zigaflow

Ready to put these ideas into practice?

Book a demo and see how Zigaflow fits your team.

Or see how Zigaflow would fit your business, free