How-to guide

How to price electrical jobs without undercharging

Intermediate7 min read
Xero IntegrationLast synced: 2 min ago
INV-1089 · Harbourne Merchandise12,480Synced
INV-1087 · Marlowe Promotions3,760Synced
INV-1085 · Horizon Events8,940Pending
Invoices synced
142
this month
Outstanding
31k
across 8 invoices

Zigaflow Editorial

Published

Zigaflow Editorial publishes Zigaflow's guides, insights, industry resources, glossary and workflow pages. Zigaflow is responsible for what they say. Spotted an error? Email support@zigaflow.com.

In short

Build every electrical price from labor hours, current materials, overhead and a chosen margin for that job. Calculate your break-even hourly cost first, then price the job above it instead of copying a going rate.

  • Build each electrical price from labor hours, current materials, overhead and a chosen margin for that job.
  • Convert paid hours into billable hours before setting any hourly cost.
  • Divide total cost by one minus your target margin rather than adding a markup percentage.
  • Treat the market rate as a cross-check after the build-up, never as the starting point.
  • Compare actual hours and costs with each estimate so the next quote improves.

Copying a going hourly rate hides what your business really costs to run. This guide builds an electrical job price in order: labor hours, current materials, overhead recovery and a target margin, with a worked example.

An electrical job is priced correctly when you add four things in a fixed order: labor hours, materials at today's cost, a share of the overhead it took to run the business, and a margin you chose on purpose. Build each layer for the job in front of you, then check the total against the market. Do not start from a going hourly rate. That rate says nothing about what your vans, insurance, testing equipment, admin time and unbillable hours cost you each year, so a job priced from it can look busy and profitable while it loses money.

This guide walks through the build-up with one worked example so you can reproduce it for your own business. The figures are illustrative, and you should replace each one with your own records.

Why a going rate undercharges

Customers and competitors quote a rate, and it is tempting to match it. The problem is that a rate is the end of a calculation someone else did with someone else's costs. A sole trader with no office, an older van and no employees can charge less than a firm with two apprentices, a supervisor and a showroom. Matching their number copies their cost base, not yours.

Two things usually get missed. First, an electrician paid for 40 hours does not bill 40 hours. Travel, supplier runs, callbacks and paperwork commonly consume 25 to 35 percent of paid time, according to one contractor pricing guide. Second, overhead does not attach itself to jobs. If you do not add it deliberately, it comes out of your own pay.

The build-up, in order

The steps below take a job from labor to final price. Work through them in this order, because each layer depends on the one before it.

1

Work out your loaded labor cost per paid hour

Start with the hourly wage you pay, or the wage you want to pay yourself. Add employer taxes, insurance, pension or benefits, and paid leave. As an example, a wage of 25 with a 35 percent burden gives a loaded cost of 33.75 per paid hour. Use your own burden figure from your payroll records, not a rule of thumb.

2

Convert paid hours into billable hours

Estimate the share of paid time you can actually charge for. If 30 percent goes on travel, collection, admin and callbacks, only 70 percent is billable. Divide the loaded cost by that share: 33.75 divided by 0.70 gives 48.21 per billable hour. This is the labor cost you must recover for every hour you charge.

3

Calculate overhead per billable hour

Total your annual overheads: vehicles, fuel, tools, test instruments, insurance, certification fees, software, accountancy, phone and any office cost. Divide by the billable hours available in the year. With 24,000 of overhead and 1,155 billable hours, overhead is 20.78 per billable hour. Keep job-specific costs, such as materials and subcontractors, out of this figure so they are not counted twice.

4

Set your break-even rate

Add the two figures: 48.21 plus 20.78 gives 68.99 per billable hour. This is your floor. Every hour sold below it costs you money before any profit is considered. Treat it as the number to beat, not the rate to charge.

5

Estimate the hours for this specific job

Read the scope and count every visit, including survey, installation, testing, certification and paperwork. Add travel and supplier collection if they are not already in your billable-hour conversion. Record the estimate so you can compare it with the actual hours later. In the example, the job needs 10 billable hours.

6

Price materials at current cost

Take off the materials from the specification and price them from this week's supplier prices, not last year's invoice. Include waste, consumables and delivery. Cable, consumer units and luminaires can move between quote and order, so note the price date and how long the quote stays valid. In the example, materials cost 420.

7

Add job-specific costs

List anything that belongs to this job alone: parking, waste disposal, access equipment hire, permits and risk allowances for known uncertainty. In the example these total 40.

8

Total the cost, then apply your target margin

Labor is 10 hours at 48.21, which is 482. Overhead is 10 hours at 20.78, which is 208. Add materials of 420 and job costs of 40 for a total cost of 1,150. To earn a 20 percent margin on the selling price, divide by 0.80, not multiply by 1.20. The price is 1,437.50.

9

Check the price against the market

Only now compare your figure with what local customers are paying. If the market price is lower, decide whether to cut scope, change the specification or decline the job. Do not quietly drop the margin. A market price is a cross-check, not a costing sheet.

10

Compare actual hours and costs after the job

When the job closes, set the actual hours and material cost against the estimate and note the reasons for any gap. If installation ran half an hour over, the next similar job should allow for it. Over time, this record replaces guesswork with your own data.

Markup and margin are not the same number

This is where many electricians lose a few points on every job. Markup is profit divided by cost. Margin is profit divided by the selling price. A 20 percent markup on the 1,150 cost gives a price of 1,380, and the profit of 230 is only 16.7 percent of that price. To keep a true 20 percent margin you need 1,437.50, which happens to be a 25 percent markup. Decide which number you are targeting before you build the price. One contractor guide notes that many healthy electrical firms aim for a net margin of 15 to 25 percent, but your own target should come from what the business needs to carry its costs and investment.

Check the denominator

A quoted "20 percent" can mean two different prices. Agree internally whether your target is margin on price or markup on cost, and use the same one on every quote.

What the going rate does to the same job

Suppose a competitor's rate of 45 an hour looks standard, and you apply it. Ten hours is 450. Add materials at cost of 420 and the quote is 870, which is 280 below your cost of 1,150 before you have paid yourself anything. Even if you marked up the materials by 20 percent, you would reach 954, still short. The job feels profitable because cash comes in, but every hour is subsidized by other work.

Keeping the numbers current

The build-up only works if the inputs are real. Review your overhead and billable-hour percentage at least twice a year, and refresh materials prices when you issue each quote. If your quoting software holds your labor rates, material costs and margin rules in one place, every quote starts from the same figures. Businesses that supply lighting and electrical work, including those in the lighting and electrical industry, often combine labor, supplied equipment and controls on one job, which makes a consistent build-up even more useful. The method is the same whatever tool you use: labor, materials, overhead, then margin, in that order.

Common questions

Markup is profit divided by cost, while margin is profit divided by the selling price. A 20 percent markup on a 1,150 cost gives a price of 1,380 and a margin of only 16.7 percent. To keep a 20 percent margin, divide the cost by 0.80 to get 1,437.50. Decide which figure you target and use it on every quote.

See it in Zigaflow

Ready to put these ideas into practice?

Book a demo and see how Zigaflow fits your team.